How to Connect Shelly Wave Plug S to Your Z-Wave Network: Step-by-Step Guide

The Shelly Wave Plug S is a versatile Z-Wave smart plug that lets you control connected devices remotely, monitor energy usage, and integrate with your smart home hub. Setting it up on your Z-Wave network is the first step toward unlocking these features, and the process is straightforward when you follow the correct steps.

This guide walks you through the entire pairing procedure, from preparing your controller to including the device and troubleshooting common issues. Whether you are new to Z-Wave or expanding an existing network, you will have your Shelly Wave Plug S connected in minutes.

What You Need Before Starting

Before you begin the pairing process, make sure you have a Z-Wave controller or hub that supports inclusion – common options include Home Assistant, SmartThings, Hubitat, or a dedicated Z-Wave USB stick. Your Shelly Wave Plug S should be near the controller during setup to ensure a strong signal, and it must be plugged into a power outlet.

Additionally, check that your controller is in a healthy state and not overloaded with devices. If you have other Z-Wave devices like the Shelly Wave i4 ANZ or Shelly Wave 1PM already on the network, ensure they are working properly so you do not encounter interference during inclusion.

• Z-Wave controller (hub or USB stick) with inclusion mode
• Shelly Wave Plug S (powered and within range)
• Access to your controller’s interface (app or web UI)

Step 1: Power Up the Shelly Wave Plug S

Plug the Shelly Wave Plug S into a standard wall outlet and wait for the LED indicator to start flashing. Initially, it may blink rapidly or show a specific pattern to indicate it is not yet part of any network. The exact LED behaviour depends on the device’s firmware, but a rapid flash usually means the plug is ready to be included.

If the LED remains solid or does not turn on, try a different outlet or check that the plug is receiving power. The Shelly Wave Plug S is designed to operate on 110–230 V AC, so make sure your outlet matches that specification.

Step 2: Put Your Z-Wave Controller into Inclusion Mode

Navigate to your Z-Wave controller’s interface and activate the inclusion or ‘add device’ mode. In Home Assistant, this is often done by clicking ‘Add Device’ under the Z-Wave integration; in SmartThings, you select ‘Add Device’ and then scan for nearby devices. Each controller has its own method, but the goal is the same: the controller broadcasts a request for new Z-Wave devices to join.

Once inclusion mode is active, the controller will listen for devices that are ready to be added. You typically have a few minutes to complete the next step before the mode times out. If your controller does not show any ready device, you may need to restart the inclusion process.

Step 3: Include the Shelly Wave Plug S

With the controller in inclusion mode, press the physical button on the side of the Shelly Wave Plug S (or follow the manufacturer’s instructions for your specific revision). The LED should change its flashing pattern – often to a slow blink or solid light – indicating that the device is being included. If successful, your controller will confirm the new device and display its node ID.

This process works the same for other Shelly Z-Wave products like the Shelly Wave i4 ANZ or Shelly Wave 1PM, so if you have multiple devices to add, you can repeat the inclusion steps for each one. Once the plug is added, you can rename it, assign it to a room, and configure its parameters directly from the controller.

Troubleshooting Tips

If the inclusion fails, first ensure the controller is within 10 metres of the plug with minimal obstacles. Z-Wave uses a mesh network, so if there are other Z-Wave repeaters nearby, they can extend the range. Also, verify that the plug is not already part of another network – if it was previously paired, you must exclude it (factory reset) before re-including.

Common issues include interference from other wireless devices (like Wi-Fi routers) and incorrect inclusion mode. Try excluding the device first, then run the inclusion again. If the LED remains unchanged after pressing the button, reset the plug by holding the button for 10 seconds until the LED blinks rapidly, then retry.

Next Steps: Configure and Automate

After successful inclusion, you can begin using the Shelly Wave Plug S to control lamps, appliances, or other electronics. Most Z-Wave controllers allow you to set energy monitoring reports, create schedules, and trigger actions based on power consumption. For example, you can automatically turn off a plugged-in heater if the power draw exceeds a threshold.

To expand your Z-Wave setup, consider adding other compatible devices such as the Shelly Wave i4 ANZ for scene control or the Shelly Wave 1PM for energy monitoring on individual circuits. With a growing network, you can build robust automations that enhance comfort and energy efficiency throughout your home.

Now your Shelly Wave Plug S is connected to your Z-Wave network, giving you remote control and energy insights. Explore additional Z-Wave devices like the Shelly Wave i4 ANZ and Shelly Wave 1PM to expand your smart home ecosystem further. Happy automating!